Chosen Solution My Impressa A9 water flow has slowed to minimal since changing my filter again. This happened once before. Sent in for cleaning/repair $$$ but do not know what they did to fix it. No longer moves enough water to make coffee or clean. Sounds like pressure builds up but no water flow. Problem solved by removing grounds tray and cleaning residual grounds from behind vertical grounds trap door. Use your fingers....
Chosen Solution My cart turns over well but does not fire I have changed the coil, fuel pump, fuel filter,cleaned contact wires. @ligordo ,Larry, Spark plugs producing weak/no spark. Spark plug gap wrong, reset gap to recommended setting, faulty spark plugs, faulty coil wires, Ignitor faulty replace, Check first all wires plugs, grounds for loose/corrosion/damage, Pulse unit faulty replace, Check first all wires plugs, grounds for loose/corrosion/damage. See link below, service repair manual with more trouble shooting and testing info....
Chosen Solution When i drive my Avenger pulls to the right alot but yesterday it seamed to have pulled hard to the left instead. So i adjusted pressure and put spare on till i got home. I put tire back on b4 driving and noticed alot of maybe bouncing in the wheel at the front left tire and alot of noise like loose brakes or something maybe but it felt like my tire was gona come off of the hub asslembly or something....
Chosen Solution There has been much discussion around 2019 MBP 16 VRM Cooling Mods to address high temps and fan noise. What tools are required, and will iFixit sell a kit with the required thermal pads? So you drank Bleach because Trump said to! This is mysticism of the nth degree! Please don’t do this! The person proposing this is not understanding how the systems heat is managed and how all you’re doing is cooking your system....
Chosen Solution I’m looking for the name of the part that goes directly over the battery. There are 2 pieces of black plastic that has to be removed to get to the battery. I had to replace the camera and my dogs grabbed these pieces off the table and they were thrown away not knowing the phone had to have them! On you tube the video of the error of phone temp too low and the yellow triangle with the exclamation point, started this was an inductor but I cannot find that anywhere!...
Chosen Solution dropped several on floor and can’t find them What model of the machine do you own? What I usually do for screws is if I have a part from a similar machine that is junk or leftover parts (Ex: BER due to multiple bent chassis parts, or a bent lower chassis with the screw needed) but I know the size is right, I’ll grab them from that - but that’s something I can do bc I have parts on hand or junk I can take stuff off of I’d otherwise be buying an assembly if I didn’t have it....
Chosen Solution I recently replaced the fan for my nintendo switch, and was not able to recover the foam tape that went between the heat sink and the fan due to some exceptionally stubborn adhesive. Does anyone know of a suitable replacement? The only thing I had on hand was a 0.5 mm thick thermal pad, so I cut that into appropriate sizes and applied it to the heat sink. Is that an absolutely terrible idea?...
Chosen Solution The plastic headband has cracked where it meets the earphone. It’s way past warranty, I need to find a replacement part and a schematic for Arctis Pro, so I can disassemble it and repair it. Check ifixgears on youtube. I think he is selling machined plastic parts you try to use. unfortunately you really cant. you can try and hound their customer support. id suggest using some kind of plastic epoxy....
Chosen Solution I have a Z1012IS. It will not turn on with new batteries. Where can I get this camera repaired? I live just outside of Memphis, TN. ridings.james@gmail.com 901 301 2829 James Ridings. I have a newer model (Z990) and I have to face the fact that if it gets damaged and I can’t fix it myself, I’ll have to chuck it. These are not pro models, and yours is getting to be 8 years old....
Chosen Solution The back cover , where the charger plug goes in has come off. It wont stay on, and i dont want to glue it. How can i get a new one out on? I have the tiny button thst you press in for readings. Thanks Ron @ruebin7,Ron, Contact fit bit at the link below for a recommended repair facility, if under warranty or close to it, have repaired under warranty....
Chosen Solution i had a iphone 6s plus that came in dead so we tested a new battery and charging port and it worked fine and charged. But when we fitted both parts it switched on but will not charge. I no its not the parts as i tried a couple of parts just in case. anyone have any ideas did you check the motherboard port for the lighting ribbon cable?...
Chosen Solution So the inside of the charger port is broken, so it wont charge anything, no matter what charger I use. How do I fix it? You will have to take it to a repair shop and have a new charging port installed. Northridgefix.com has a huge selection of charging ports and should have the charging port in stock. You should check them out on their website and get a quote....
Chosen Solution I was using my camera the other day at my job. When I put it into its bag without turning it off first. When I took it out of the bag later and realized it was still on I noticed that it was in some weird setting that I had never seen before. Since then I have been getting photos that do not show the true shade of the actual image....
Chosen Solution Hi, I have Samsung side by side fridge freezer. The fridge is freezing food at 7 degrees C. What could be wrong? Hi @cverster Run the diagnostics and check if any error codes show.
Chosen Solution The amplifier keeps blowing the mains fuse and i found R145,R170 are melted on the pcb can you help me fix this problem? Step 1: check output stage. 2:power supply components. 3: check board for any leaking cap’s. If these are glass fuses chances are you have a output transistor or transistors that has went bad. These devices are in place to provide sound in the speakers through a chain of other components....
Chosen Solution The port in my JBl pulse is bust , there seem to be no open screwholes or anything to take it down, i wanna know how to repair , it This guide shows how to get inside JBL Pulse Motherboard Replacement
Chosen Solution I dropped my phone at the beach for 5-10 seconds before I picked it up. Everything is fine but the speaker doesn’t work. How can I fix that???? Please help!!!!!!! Hi Briann Bravo, Was the phone dropped into the water or only onto the sand? If only onto the sand then here is a link to the iPhone 6 Plus Speaker Replacement guide. This will help you to gain access to the speaker to ensure that it is still connected properly or if it has to be replaced....
Chosen Solution have to remove plastic cover to work on wires goin to lock @robertog page 34 of this part of the SM Versa Exterior Interior explains how to remove it. Now this is for a 2012 since you did not tell us which model year yours is. The steps in principal should still be the same.
Chosen Solution Urgent help is needed. I Have a Toshiba tv, type 58L5400U that was manufactured in August of 2014. The tv continues to turn off and on after displaying “Toshiba” on the screen. Haven’t had any issues with the tv until now. I’ve tried unplugging the power source for long periods of time, I’ve also used a different outlet location. Someone said to try taking the power cord out and holding the power button down for 30 seconds to reset, this doesn’t work for me either....
Chosen Solution When I try to log my WiFi to the viking pro it says authentication problem Hi, Have you tried “forgetting” or deleting the WiFi network connection from the tablet and then setting up the connection again? To forget the network, press and hold the appropriate WiFi network connection until an option box appears which will allow you to delete the connection from the device. Then scan for and select the WiFi network and setup the connection again....
