Chosen Solution So, I’ve fixed many iPhone screens and I’ve never had this issue before First, after the screen had been assembled onto the device, I boot it up by plugging the charger in as I always do. The screen seemed to be working fine as far as touch functions are concerned. I allowed it to charge for awhile before giving it back to the customer So, before I went to work, I turned it off....
Chosen Solution So the iMac I have gotten it hard disk drive is dead. I’m wondering if I can fix it or if I haft just buy a new used hard drive. If I can’t repair it we’re can I possibly buy a new hard drive. Thanks for any answers or advice for the question not sure about a 13GB model but the Apple parts number for the G3 Hard drives are as follows: 661-2372 7 GB 661-2373 7 GB 661-2344 10 GB 661-2361 10 GB 661-2327 20 GB 661-2335 20 GB 661-2336 30 GB 661-2362 30 GB The drive itself is a 3 1/2 inch ATA-100 (40 pin IDC) drive....
Chosen Solution I’ve been using my label maker for a while and will probably start to run out of paper soon. I was wondering how I go about replacing the roll of paper in the label maker? Remove the lower lid of your Brother PT-90 Label-Maker device, and take out the used label cartridge. Replace with a new label cartridge (these cartridges can be easily found for sale online.) Refasten the lower lid, and you’ll be back in label-making business!...
Chosen Solution Samsung 58” smart tv model un58h5202afxza . picture when out put new power board in . Now I have picture again . But still have a burn smell so I looked at the new power board and it as a burn on it. Still works .What is causing it to burn a spot on left size of the board . Update (08/19/2018) * Without seeing the actual burn mark, I can’t be 100% sure, but… In the general case, burn marks often show up around resistors....
Chosen Solution My brother has a “Corsair K95 RGB Platinum” and he smashed the keyboard. Because of this incident I had to replace the x key on his keyboard. But after replacing the broken key with a new key, the keyboard acts out and presses every key in the row(Shift z x c v b n m , . / Z X C V B N M < > ?). Is there any way to fix this issue?...
Chosen Solution I’ve been googling for a while now and have failed to find it, I had to do a board level repair and needed to remove these little foam adhesive strips surrounding the battery, display and wifi diversity antenna connector on the logic board. Unfortunately, I messed it up pretty badly removing it and I was hoping to buy a new one. I’d assume they are just there for water proofing, but the state of mind of having a complete phone has made me interested in seeing if I could purchase these....
Chosen Solution I need a wiring diagram for the indicator section mainly, but a complete wiring diagram would be more useful. I would ask the local dealership if they could copy the pages for a fee. That is the best way I can think of. Or you can find a repair shop with Mitchell that can print you the pages for a fee. Some auto parts stores can also do that....
Chosen Solution My charging port is damaged and I need to know how to fix it I don’t know how damaged your port is, but I assume you want to replace it? I’ve never done this myself, but I don’t think it’ll be easy; you probably need some skills with soldering. This is how I assume the process would go: First, you’ll need to find a donor device that has a working, mini USB port (a cheap, broken TI 84 Plus CE should do)....
Chosen Solution Hi there, I was wondering if you guys could help me out. I upgraded my i3 to an i7 870. Since then after the first sleep after reboot the temp sensors are not available causing the iMac to sleep every 5 seconds after that. Any ideas? Well… You used the correct chip so thats not it. At this point I suspect you either failed to connect the sensor cables back in correctly or you damaged something on the logic board in the process....
Chosen Solution Hello Guys I had a water spills on my my MBA 11 and since cleaning the board etc. its in near working condition. Two problems remain: Power button does not seem to work, no biggie as I can get it to boot by plugging in the power cable and it automatically comes on. I have looked for shorting but cannot find it. The fan will come on halfway though boot up at 6500RPM and stay that high!...
Chosen Solution The computer does not switch on and fan starts turning non-stop. No lights on screen and only fan turns. Any idea what can be? In a computer repair shop (apparently very bad) just only told me that motherboard (logic board) is kaput. Is it really only the motherboard? To me it sounds like the battery or the logic board The ramped up fan tells me SMC encountered a severe problem with one of its sensors!...
Chosen Solution I have tablet asus tf 300 I charge the tablet until the LED turns green, press the power key and the tablet does not open. I replaced the battery and the problem was not resolved. Has anyone encountered such a problem and what is the solution ?? yunissm consider trying a hard reset. Use the instructions as outlined on here
Chosen Solution I repeat my question a little more clearly, what I want to know and the reason for it, I would appreciate an answer for it. I have a 4-IN, regular connector USB and, 1-OUT Mini USB connector for use in my APPLE Minibook and use on it. If it possible to charge the computer’s battery. also and I want to know if the position of the + and - voltage connections, if they are in both compatible between the output and input of one and the other....
Chosen Solution Hi there I have these problems with my mbp 15" mid 2010. Last four digits of the serial number is xxxxxxxxx-RAGU. the logic board number is 820-2850-A. The symptoms are very high fan speeds. Does not respond normally to power button. Only boots into emergency mode. No lights under keyboard. date and time are not set properly. indicator light flashes every 2 seconds. Tried resetting/flashing SMC through shell but didn’t work....
Chosen Solution This TV did have a burned out (blackened, actually) LED on one of the backlight strips. I replaced that whole strip, and all the backlights are now working/steady, with no blinking… unfortunately, there is no longer any picture on the screen. Before, when the backlights would flash on, I could see the LG menu and screen, but now there’s nothing, just a dark-gray screen. So, it looks like something went wrong when I disassembled the screen to fix the LED strip, or when I put it back together....
Chosen Solution Hi, I just replaced the touchscreen on an iPad Mini. The repair was done with the utmost care, but once laying the digitizer back down flat on the chassis, the touchscreen starts to register jittery and random input. Once the touchscreen is lifted off the chassis, the problem goes away. Seems to be only when the digitizer makes contact with the aluminum frame. If any one has any information on why this is happening and any possible fixes I would be very great full....
Chosen Solution Yesterday, my Macbook’s trackpad started bugging out. Moving by itself, clicking and zooming on its own, hardly usable. Doing some research, I found that this is a common issue due to the battery aging, swelling, and pressing upwards on the trackpad. Although the battery only has a little over 500 cycles on it, and coconutBattery says all is well, I started looking into replacements. Being the frugal person I am, I decided to take out the battery and see for myself if that’s the actual problem before purchasing a new one, and the battery doesn’t appear to be swollen at all....
Chosen Solution hi everyone I just bought an iBook G3 clamshell graphite firewire model m6411 it’s in a very good condition, nothing is broken or so. but when I turn it on it works but no chime at the beginning and a black screen here is a video I took of the problem https://www.youtube.com/watch?v=mdKdAZQO… I’ve red around in the forums with no lock I’ve reset the PMU and it didn’t solve it I’ve tried it with and without the battery and it didn’t solve it I’ve replaced the Ram even tho the iBook dose not make any “beeps” at start but still no luck any idea what might be the problem and is there anything to try doing?...
Chosen Solution I have a 500g hard drive (250 each) and want to upgrade it to 1TB SSD. Do I have to use 2X500G SSD’s or can I use one 1TB SSD for the upgrade? What kind of software can I use to migrate the HDD to SSD? Hi @manjulad . I assume that you have one 500GB HDD that has two partitions of 250GB each or did you replace the optical drive with a HDD so that you have two HDDs?...
Chosen Solution I have a rose gold iPhone 7, A1778, unsure of any other specs, and it needs to be reset as it is currently disabled. The volume down button doesn’t work, so i am unable to enter recovery or DFU mode. It also has “unlock iPhone to use accessories” so it’s not recognized by my pc. When i replaced the button flex cable, it still did not work. Put a different board into its housing, and all the buttons work fine....
