Posts

Chosen Solution Hello, I could not find the Pioneer VSX-925-K receiver in the device list. The PQLS light flashes when the unit is turned off, and if I press the power button to turn it on, it turns back off by itself after about a second. I have found the service manual for the VSX-1020-K which according to some info I’ve found is very similar to the 925. It says in the “error indications” section that a flashing PQLS light means ““Abnormality DC voltage of the Digital power supply” detection”....

Chosen Solution Two days ago I was cleaning my pool when I accidentally fell in for about 5 seconds. I got out and laughed about it, until about three minutes later I realized my phone was in my pocket, right then panic set in. I had no idea what to do so I checked to see if the phone still worked by just hitting the home button, it did, but it looked like it was glitching and showing these small aligned squares in the middle of the screen (mind you the phone will still soaked when I did this)....

Chosen Solution What can I do routine maintenance for my truck it’s got a lot of miles on it Shawn Jones main thing is that you continue your routine maintenance. Regular oil changes with High-Mileage motor oil is pretty important. Change your spark plugs, belts, filters etc. at regular service intervals. Pay attention to the cooling system (hoses, radiator etc) There is nothing really special about it other than do not let little things build up....

Chosen Solution Hole is approximately 1mm. Located on the top deep side. Do you mean the front-facing HD camera? I think he means the ~1mms diameter hole ~7mms centerward from the headphone jack. Without investigating further, I’m guessing it’s the microphone. When I took off the case, I found something. I have no idea what it is. If you hold your fire tablet to where the volume and off button is facing your right, and then face the tablet upwards, then look at the right of the thin part, you’ll see something that looks like it can be opened....

Chosen Solution Does anyone know if the Display removal process of this machine is the same as it is in the 2019 model? I don’t why it would be different. Apple didn’t alter the display hardware, but it is a different P/N from the 2019 version! The biggest issue is finding the part as the system is still under warranty coverage! 13” MacBook Pro 13" 2020 Both 2 Port and 4 Port systems Display Assy: Space Grey, Apple P/N 661-15732Silver, Apple P/N 661-15733 13” MacBook Pro 13" mid 2018 & early 2019 models only....

Chosen Solution do I drop the subframe @scfoster according to the manual you need to : Disconnect the negative battery cable Remove the battery and the battery tray Remove the air cleaner component Remove the front tires and splash shield Remove the steering gear and power steering pipe Remove the front auto leveling sensor Drain the atf Here is the part from the manual that describes the automatic transaxle etc. Mazda_6-Automatic-Transaxle....

Chosen Solution The outer glass panel is cracked on my phone and I want to repair it.. I don’t know what glue I need to do this tho as I already have the new glass I have used this glue for repairing a similar phone. It worked well for me!

Chosen Solution I want buy motherboards beats pill XL… where and how much..? You cannot find replacements as they were recalled awhile back. https://support.apple.com/beats-pillxl-r…

Chosen Solution I have a 2008 Volkswagen Jetta Wolfsburg Edition 2.0 T. I need to replace my camshaft position sensor but can’t find the location. Anyone know where it is located. I’ve found videos of the position on other years but none of them match mine. On the CCTA 2.0 TSI the sensor is located on the valve cover directly above the intake manifold. The connector will have three wires and a standard Bosch connector....

Chosen Solution Everytime I attach the battery or plug the charger the tablet won’t turn on but instead it overheats. The heat come from where the processor is and it get very hot. I used a multimeter to see if there are some power supplies issues and the battery looks fine with 3,7V. I already tried disconnect and reattach the battery but it still doesn’t work, even tried to plug the charger without the batery and still the same....

Chosen Solution My machine worked fine and then was inactive for about a year. (Not exposed to extreme temperatures. The machine still works but the brew head leaks a lot of water. The valve spring probably just needs to be retensioned; give it a good stretch, make sure the silicone valve nipple and seat are clean and put everything back together. Check the o ring where the filter holder locks in is not missing or damaged....

Chosen Solution I went to start the car after sitting all night, and it would crank, but not fire. When I got out there was a strong odor of gasoline. When I removed the air cleaner cover there was gas puddled in the air cleaner. I’ve disassembled the carb, and find no obvious problems like a stuck float or anything. What’s the next step? @gregoryp since you’ve obviously done this kind of work before, I am certain your carburetor is fine....

Chosen Solution Electricity is not up to the motherboard yopu must test it with charged battery first if worked with charged battery you must change the fdmc upload your motherboard picture and test as i said to you

Chosen Solution when I turn on my camera the viewfinder will not show anything. Hi, Does anything show on the screen when you press the DISP button? Try taking a picture (I realize that you cannot “see” what you’re taking) and then download it to a computer. If the picture is OK then there is a problem with the camera’s LCD screen. If the picture is just a black image, then there’s a problem with the camera’s image sensor or the motherboard

Chosen Solution I cannot run my e-bike with the headlight on. Whether on low or high beam, the bike shuts down if the headlight is turned on. Hi, There is three things is it fully chargedis the battery bador shorted Hope it helped

Chosen Solution Hello, I recently replaced my LCD and I might have pulled too hard on the flex cable when removing the metal backing plate as when i put the phone back together everything worked except touch id failed. So i ordered a new home button flex cable and when i replaced it, touch id initialized but did not recognize a finger. The fingerprint comes up but does not turn red to recognize my finger....

Chosen Solution all the other buttons are working except the touchscreen and the back button how we can repair touch pad doesn’t work Hi how are you Can you tell us, is the screen broken? how did it get to this situation, fall, stepped on ……..? Do you want to fix it yourself or going to put it into a shop? They are not that tricky to fix , on a scale of 1 to 10 they would be a 4 a little more info please :) Regards Charlie

Chosen Solution I left my phone in my bathing suit pocket white I went to the beach. It was in there for about a minute or 2 in shallow waters before I realized and immediately left the water to dry it. The phone operated fine after taking it out turning on and being able to open it and use it. The only problems were the Face ID wouldn’t work and it didn’t recognize the SIM card....

Chosen Solution Hello my fellow geeks, I have a problem with my iphone 5s touchscreen,part of my screen do not respond at all. To be more precisely almos half of my screen doesnt work. I have never had one of those, but if you go to settings and enable screen magnifier, you can tap twice and it will make the screen larger. you may also be able to pinch in and out to enlarge it....

Chosen Solution I read the Pencil teardown and understand that the outer plastic and inner metal shell needs to be destroyed. Are the electronic components still working after this procedure? Is the metal shell essential or is it a safety measure in case the battery decides to expand/explode? Just food for thought: I have a 3d printer and wonder when the battery dies by age and usage if it is possible to either print or misuse a real ergonomic pen casing to transplant the electronic innards and additionally exchange the battery circuit to a swappable 3,7v ±5% AAAA sized battery and maybe add a on-off switch....