Posts

Chosen Solution BOSCH washing machine front loader. Choosing cold water however inside was very hot. Water supply is connected to a water hose. In gentle mode can wash at 30 degrees. In other modes, the inside of the washing machine is hot and the drainage is very hot. I wanted just washing with just water! What is the problem? Hi, I can’t find a user manual (or any other information for that matter) on your particular model but I did find a user manual for a WAE 20161 which I hope may be close enough to your model to be relevant (for a start they are both WAE models)....

Chosen Solution dishwasher works but sometime later water appears in the bottom Hi, What is the model number of the dishwasher? If there is no standing water at the end of the final cycle but it appears later on then there may be a problem with the water inlet solenoid valve not shutting off fully and water is slowly leaking into the machine. To check if this may be the problem, at the end of a complete wash cycle check that there is no standing water at the bottom and try turning off the water supply to the dishwasher....

Chosen Solution Hello there, I am getting F4- E3 fault code on my whirpool dishwasher ( WDT970SAHZ0 . It seems like dw gets fill with water and then it drains This code calls for problem in drainage. I have checked inside of the dw for blockage and cleaned filter and the water sensor. Under the dw I check for glass or anything blocking the drain pump and hose. I unplugged the dw to reset it to see if that clears it out....

Chosen Solution My daughter put in a new keyboard for her MacBook pro 2012 but could not put the rest back together so I am trying to help. There is a wire in upper right corner coming from frontside that I can’t recognize. Does it go to keyboard or display? I don’t see a photo yet but the only thing coming off that keyboard should be the power on button. UPDATE 7/25/17 Thanks for posting a photo....

Chosen Solution My keyboard isn’t always responsive to me while I am trying to type. Sometimes it doesn’t work at all and i have to power off and on my laptop, which sometimes momentarily fixes the problem. And at other times it only works for certain keys while I am typing or it types everything I put it but only after a few seconds delay. This is very difficult to deal with because I’m just trying to get some schoolwork done....

Chosen Solution My laptop has been losing screws over time and now I only have 4 left out of 9 and feel like it’s going to fall apart! I have been trying for a while to replace them but have struggled to find the size or somewhere that specifically sells these screws that’s available in Australia or ships to Australia. Could someone tell me the size of the screws for the ASUS Zenbook UX303L?...

Chosen Solution I dropped it face first and it turns on sometimes, registers im touching screen but like does a quick flash and goes back to black, no scratches or such but it does seem not very well working. Wjat should i do ? Is a screen replacement, solution? Whats the cost? Here’s the part: https://www.digitalsupplyusa.com/product… Here’s a video on replacing it: https://www.youtube.com/watch?v=U5F-rh3m… It will cost you approximately 60 USD if you do it yourself but if your are not experienced I recommend you taking it to a phone shop and getting fixed it may cost up to 100

Chosen Solution This laptop cannot run modern games without lag . So can I upgrade this model or i need to buy a new one ? Hi, There’s nothing that you can do to improve the performance of the laptop except perhaps to replace the systemboard if your particular model variant doesn’t already have the highest system specifications systemboard that is available for the laptop. The memory (4GB or 8GB max....

Chosen Solution Car not shutting off Hey there if your car won’t shut off the first thing you should do is pop the hood open and disconnect the battery to shut it off the second thing is that you probably need a new ignition or you have a wiring issue I would look at your key to see how worn it is, this will give you a clue as what the condition of the ignition may be....

Chosen Solution I was repairing my ps4 slims cd drive and this piece fell out and I have no idea where it fits in does anyone have a idea where it’s supposed to be? I had the similar problem while repairing mine as well but found it out after sometime. Position the arm cover plate so that you can see the black arms. Push outward on those arms and slide up on a white stick on the under side of the plate which will be located under your right hand....

Chosen Solution The “power button” light is on, and wont turn off. No other buttons work or respond. When phone is connected to the JBL Charge 2+ it appears to charge the phone. Thanks for any advice if anyone has had similar problem. Update (06/30/2018) thanks to Jayson Van Camp removing/unplugging the battery and then re-attaching worked for me. thanks to Jayson Van Camp removing/unplugging the battery and then re-attaching worked for me....

Chosen Solution Hi i tried to power on my xbox 360 s because my xbox one x asked me to purchase a game on a xbox 360 my xbox worked fine last time i used it ans has been unplugged on a shelve ever since. Now when i plug it. The power brick turns from amber to green which is ok and stays green until i power off the Xbox so i guess it works fine but on the xbox the center of the power button turn green than turn solid red 30 sec after, the fan works while it is red and the disc tray works fine and it seems to be reading the disk i pop in But i cannot sync a controller or get an image on the tv i did the light test pressing on sync and eject all 4 circle lights are green but that standard light will stay on red i couldn’t find any info on the troubleshooting here neither on Microsoft....

Chosen Solution Everytime I hit reset or I turn ut on. The screen turns white then random colored lines appear. After a while of hitting reset it randomly turns on and off. The only way to turn it off is to hold reset. Oh, that sound fun. So obviously RAM resets aren’t working. Have you tried charging the battery all the way? That’d probably be the easiest possible solution. However, I don’t think it’ll work....

Chosen Solution wiring diagram for the solenoid Hi, What is the year and model number? Here’s a link that may be of some help. Find your model number on the page and then click on it and select the Electrical option that appears in the parts catalogue section menus on the left side of the page to get a wiring schematic. Here’s an image for a 1997 13AL452F120 model, just to show maybe what to expect....

Chosen Solution Hi I know there’s bits about this already. But hoping there’s more of a definate answer? Had a 6s come back to me, which has been working well for over a year, the chap upgraded to IOS 11, and now the touch does not work. Plugged in original screen, and it works. What’s the deal here? Apple will obviously sort it…. for £150! Duane check the answer by @refectio on here After update to iOS 11 Touchscreen unresponsive...

Chosen Solution I purchased two screens from an eBay store after smashing my screen. Both had a small issue fitting the bottom of the chassis after repair, but managed to be closed. Anywhere from five minutes to five hours later it’ll work, then stop working until I turn it off and lift the screen out and restart the device. Any ideas? Firstly thought it was a dud-screen which is why I got the replacement....

Chosen Solution My VisionPQ65-F1, while watching will lose the backlight. Picture is still there (flashlite test) and sound is still there. I turn it back on and it works fine for 20 minutes, then the same thing happens? What is going on? I have done a Power Cycle and a full reset to no avail. Hi Allessio, It sounds like it could be a software issue, loose connectors, or bad backlight driver boards....

Chosen Solution We had a storm and my tv died. No power - no standby light… I tested the power board and determined it was bad. I replaced the power board. When I plugged it back in, I get a red blinking light (8 blinks). I tried following trouble-shooting for the limited info I could find to no avail. I then found something about holding the power button in as you plug it back in....

Chosen Solution I have an issue with my mac book pro A1502 which shows in the picture below two vertical lines starting yesterday after replacing the WiFi card. when I tried to connect it to an external display it worked fine. I also tried resetting NVRAM/PRAM and SMC but did not work hi @pascalito, replacing a wifi card would not cause this type of issue on the display. this looks more like damge caused by dis/re assembly of the unit or perhaps a failing chip on the tab of the display itself....

Chosen Solution My screen unable to touch but the fingerprint sensor still working Hi, It seems as though there is a problem with the digitizer. (touchscreen) Has the phone been dropped or gotten wet at all? If not as the phone seems to be a very new model, if it is <12 months old from new, contact the Samsung customer service section in your location and get it fixed under the manufacturer’s warranty provisions....