Posts

Chosen Solution I have all the updates and in device manager show me a warning and if I enter to properties tell that the device won´t work properly that I need to restart , but I restart several times and the problema continue. Hi Cesar, While it is possible that there is hardware damage, it is equally likely (if not more likely) that the drivers are not doing their jobs. I find this especially likely if you have an explanation point next to one of the devices in Device Manager....

Chosen Solution My husband went to buy me a bigger tv for my livingroom.I then put my old tv in my bedroom.I have a window unit that gets it freezing cold in there and now each morning I go to turn it on,there are stripes in the middle of tv,WHY? Hi @rj3948 What is the model number of the TV in the bedroom? Cold contracts, heat expands. It sounds like there may be suspect screen connections on the cables that go from the tcon board (or the mainboard if not separate boards) to the screen....

Chosen Solution when i turn on my ps3 system turn green and orange and red blinging any idea whats the problem with this console thanks that is the yellow light of death (ylod)….there are all kinds of guides on here on including a fix kit for this problem….if you need a reference the ylod is very similar to the xbox 360’s rrod. Hope this helps. Good Luck, Cody Hello, it sounds like you have the famed “Yellow Light of Death....

Chosen Solution Samsung UN46D6400uf the tv flashes on and off with the logo every time I attempt to turn it on. There is also an audible click. note. Audio in clip is not coming from this tv. Update (09/05/2019) KC wilkinson remove the back from you rTv and unplug the main board from the power board. You should now get the backlight to turn on (you can check by looking at the back of the panel though some of the screw holes to see if it is on)....

Chosen Solution Title says it all pretty much. I was using compressed air to clean the mic grill of my Pixel 4 XL and the rear glass started lifting up/inflating slightly from the frame. I think air was coming out of it. Did this just damage any of the water resistant seals on the phone? The rear glass went back flush with the phone and it doesnt seem as though anything is damaged....

Chosen Solution Hi, my niece tv has a band of coloured vertical lines on the right side of the tv along with a couple of horizontal lines along the bottom of the screen. The tv is only 2 months old. I have been in touch with Toshiba and sent them photos and they are saying it’s not a manufacturing fault and that it has happened externally. My niece said the lines just appeared and there is no visible damage to the screen itself....

Chosen Solution my iPhone 5, which suffered some water damage few months back. I left it drying for a few months, turned it on and it was working again. In the last few days, since updating the software the phone was working fine, until it ran out of battery (playing music all afternoon). Now trying to recharge it and the phone won’t turn on at all. tried pressing both the power and home button trick and didn’t work....

Chosen Solution So i dropped my iPhone SE in the water and it stoped working. I replaced the battery and the charging port but it still won’t turn on. I was wondering if i need a new phone or if it is fixable. Hi @bradyjordan1109 , As you know liquids and electronics and electricity are not a good mix. The liquid causes corrosion and provides circuit paths for the electricity which were not in the phone’s operating design and could damage the components....

Chosen Solution My sons phone was in the washing machine for about 5 minutes. I extracted and put in rice and then on top of hot water cylinder. So now it starts up ok, but the home button doesnt work (have assistive touch option activated) so this is not a major. But now when he tries to charge it, it comes up with the ‘plug into itunes’ picture. When he does, it says it needs to be updated or recovered....

Chosen Solution Hi, So I have been recently having some issues with the webcam on this Macbook Air (Early 2014) where it would work, but the image would break up and it was a bit hit and miss whether or not you’d actually get a clear image. So I replaced the webcam, and since then, the webcam is not recognised at all, and I get an NCD001 error when running Apple Diagnostics....

Chosen Solution I want to add ram to my laptop and want to kow how much I can install. RAM Technology DDR2 SDRAM Installed Size 4 GB MEMORY Max Supported Size 8 GB Technology DDR2 SDRAM Form Factor SO-DIMM 200-pin Slots Qty 2 https://www.cnet.com/products/dell-inspi… While the maximum RAM limit for 32-bit Windows editions is 4GB, when it comes to the 64-bit editions, the amount of memory that the OS can address depends on which edition you are running....

Chosen Solution I can see one on the battery and one is visible once the battery is removed. Where else ? What about the white bit around the trackball ? Thanks! As near as I can tell, there aren’t any more. See: Nexus One Teardown I saw one little circular white spot at the charging hole at the bottom of the device. Maybe that it’s? There is a rectangular water detection sticker on the battery, next to the connection points....

Chosen Solution Hi! Very helpful video! I have dust on my camera. I tore don the phone, cleaned the lens and used a rocket blower to blow the dust but it stays there. When I remove the main camera and move it around, still connected, the dust particles do not move with the picture , therefore the dust must be somewhere else inside the phone… Seems its on the sensor and the sensor is not part of the lens....

Chosen Solution Does anyone know what exactly the differences between the 2010(/11) and 2013(/14/15) top cases are? I’m trying to find out if I could replace the top case of a 2015 Macbook Air with one from a 2011 model (for keyboard replacement). Any ideas? Apple moves things around as well as upgrades some of the components which makes it difficult to do assembly swaps like what you are looking at here....

Chosen Solution I keep getting the following error: Top tray jammed. Pull tray out. Press OK to continue (code 3550). I pull the tray out… then I get the following: Top tray jammed. Push tray in. Press OK to continue (code 3551). Soooo, I push the tray in… and the errors just keep repeating themselves! There are no jams, trays, paper, or foreign objects of any kind! Is there any way to disconnect use of the top paper tray?...

Chosen Solution I need help to get my touchpad working again but really need help to do this so please help if you can? Open control panel and search for touchpad or any third party software using earlier open the panel by double click on it. check if it is enabled if yes first disable it and enable it after restarting the laptop hope it will work.

Chosen Solution I’ve had this plasma TV for about a week (second hand). What I’ve noticed is that when the TV is displaying a lot of white, the whole display quickly but gradually dims. When displaying other solid colors (red, blue, green), the image is truly vibrant, so it is not the pixels themselves, apparently. This makes me wonder: could it be possible that the TV cannot draw enough power to power all colors at once to display a lot of white properly?...

Chosen Solution I have a Sony UBP-X800 which not read any disc, so I need to replace the optical unit, but in the SERVICE MANUAL says that in order to make the change first I need to take a picture of the Bar Code on the Optical Unit and load it into a software called " UHDBUDecode.exe " and save a text file, then save it into a USB and load that file into the UBP-X800 ub port…....

Chosen Solution I’ve been using the tablet ALL day, and now every time I try to type something anywhere a dark gray box pops up saying “Unfortunately, Goggle Search has stopped.” It is really getting on my nerves and I can’t go on anything at all! -.- Also, the WiFi went down so I can’t even play the games I installed earlier… ;-; How do I get rid of this thingy…?...

Chosen Solution after replacing new battery ups not on online mode Hi Santhosh Any symptoms? like blinking online LED? Try this method and see if it works https://www.youtube.com/watch?v=lioxJe0U… Plug the Back-UPS into the utility power source. The Back-UPS will be in a Standby Mode (no indicators lit). Press the front panel pushbutton fully inward for 10 seconds. All indicators on the Back-UPS will flash to acknowledge going into Programming Mode. The Back-UPS will then indicate its current Sensitivity Setting....