Chosen Solution Touch was left outside in the grass several night. Cold and “moist.” Cant make it come on. – charging now, bottom feels warm, but no life otherwise. Should I send in to a repair center or just trash it? Don’t trash it! But unplug it and leave it in a bag of rice for a couple of days. After that, try turning it on. If rice doesn’t work, you could attempt to take it apart and let it dry piece by piece....
Chosen Solution my home key is working but i try to put my touch ID it’s say fails Either the home button has gone bad or has been replaced before. It can also be caused by liquid damage. Usually requires cleaning up the home button connector with isopropyl alcohol near the home button if it is corroded from liquid damage. When replacing the home button there will be no touch ID as it only accepts the home button that came with the phone for touch ID....
Chosen Solution Hi Guys, I have a friend’s 6s Plus that has had a screen replacement and is now not responding to touch. The iPhone was initially repaired at a local phone shop, although it only cost my friend £60 and therefore I assume that it was either a cheaper aftermarket screen or it was not a full replacement. However, after a while, it either stopped responding to touch and was then cracked again or the other way around (my friend is unsure)....
Chosen Solution Turns sharp left but very little to the right @rjr3 could be tie rod issue as well as a steering spindle issue. It will help if you can provide us with the proper model number of your Craftsman. Even better would be to take some pictures of your steering components and post those with your question. Here is a guide for that.
Chosen Solution So my vizio tv display will go grainy after turning the display off then on, if there is still an input going to the tv the the whole display will become grainy, even the tv menu. Logan Wisdom number 1 cause for a grainy picture is the T-con board and after that the main board. The panel is always a possibility. So I suggest you start with the t-con board....
Chosen Solution Our Toshiba TV has picture but no sound! I tried using external speaker but still nothing! robbie, since we still do not quite know which model your set is, here is a flow chart for a 2009 series 40RV52R, 40RV52RZ, 40RV525R, 40RV525RZ for the “no Audio” error. This is where the importance of knowing what model you have and possibly seeing your boards. Once you have the model number, remove the back (unplug the set of course) and take lots of pictures....
Chosen Solution I have procured one TV from Toshiba authorized dealer in the year of 2014. There was no problem in my TV since its procurement. But yesterday suddenly , the screen of the TV became back but I am listening the sound of respective channel. When I flash the light the pictures became visible lightly. I’ll glad if anyone from your company help me to solve the issue and provide me the service engineer details of following area to repair the TV....
Chosen Solution Hi, what may be my problem? It’s not T-CON or Ribbon cables. @mountpleasure not sure how you determined that it is NOT the T-con board. If you are absolutely sure about that, then the only other possibility is a bad panel. The LCD driver board most likely has some bad drivers.
Chosen Solution While replacing the broken screen, I found this metal piece that fell off. Can someone identify what is this and where do I need to put it back to? piece That looks like one of the grounding metals of the speaker and antenna module. Your phone should work normally without it.
Chosen Solution I bought a LaCie Blade Runner 4TB HD. I don’t have a need for the storage and would like to replace the HD with a 1TB Samsung EVO SSD and give the HD to my son. Is there anything in the hardware/ firmware that would make this a problem. I recently managed to put SSD’s in 2 older iMacs. There is no fan in the LaCie now - so that shouldn’t be a problem....
Chosen Solution My ram memory is now 3GB. I know that this is the maximum I can have for MBP 15 A1211. If I will try with more, will it be recognised? Yes, it will take two 2s. http://www.everymac.com/systems/apple/ma…
Chosen Solution Is there any way I can upgrade the hardware on my iPad 4 Gen Wifi? No matter how many times I do a software update, it stays at IOS 10.3.3., would putting in a better logic board do it? Can I bump up the resolution on the display? And can I also upgrade the camera to take better pictures? The iPad 4th gen has a 5 Megapixel rear camera and a 1....
Chosen Solution My USB piece of cable on my turtle beach earforce xl1 headphones got cut when I stripped some of the black covering there is only insulation and red wire with what looks like some copper in it, is this simply sader together use some shrink wire and it should work? Or is it more complicated because of this funny looking red wire if u would like a picture of what it looks like I can send u a photo via email....
Chosen Solution So about six months ago I accidentally dropped a glass of water on my Macbook and I took it to my local apple store and they told me it had water damage and needed massive repairs and I should just buy a new one because it would be cheaper, I didnt have the money for that so I took my broken laptop home and left it in my wardrobe for six months and the other day I was cleaning out my wardrobe and found the charger for the laptop and wanted to sell it but didnt know if it was workable as it got slightly wet in the water incident, I thought maybe I could plug it into the broken Macbook even though it doesnt work maybe somehow it would work and upon plugging it in the charger lit up!...
Chosen Solution Hi Everyone, I hope someone out there can help me out. I have to replace my Logic Board in my MacBook (2008, White 2.4GHZ 13" Penryn, A1181) after an unfortunate soda accident. I know that I can swap out the board with certain others that are different speeds, & I’m considering this option b/c I need the cheapest possible board! I need to know all of the different Logic Boards, including the different speeds & the corresponding part numbers for the boards, that are compatible with my MacBook 13" 2....
Chosen Solution , I have a lenovo idepad duet 3 10ilg5 but their doesn’t appear to be a teardown of this device Edit here’s the pdf but when I search online can’t find anything on the screw I can tell you that it’s a Torx bit, but it’s hard to see what size it is and I can’t find it online. But I would guess the bit size is somewhere between T3 to T8....
Chosen Solution Have an Aspire 1 that I still use almost on a daily basis (some old programs on it that don’t do well with Windows 10 (on another computer). Anyhow, it suddenly died on me, red light for the battery charge constant. Bought new battery and left it on charger and it charged good (green light again). Now, the computer turns on and basically nothing other than a green light for the power switch....
Chosen Solution I was wondering what adhesive I should use, that will be watertight and waterproof too. Any dual stage epoxy would do but it will be messy, smelly, hard to apply, and difficult to clean up…. but it will be air/water tight (assuming you applied it completely and correctly) and vibration proof (of this use case). You can do it… don’t use a fast curing epoxy because you’ll want time to apply, attach, clean-up the epoxy....
Chosen Solution I uploaded an image of the part. @rhempz01 that is an inductor. The R represents the decimal points and the 33 is the inductance. So in your case it is a 0.33uH inductor. BTW your components all look like they have gotten pretty hot at one time. Double check on that. Remember that there are no schematics available for most video cards. So you’ll have to do a lot of guessing....
Chosen Solution Samsung Galaxy A70 Accidently broke it :( Hans, If I am correct, that is part of the antenna system. I have knicked one before when taking the back off. That incident did not seem to have an affect on service, but I cant speak as to a full tear. Best advise is to reassemble and see how the service is. I hope this helps! Roy
